- 您现在的位置：买卖IC网 > Sheet目录985 > ISL29020IROZ-EVALZ (Intersil)EVALUATION BOARD FOR ISL29020
ISL29020
Pin Descriptions
PIN NUMBER
1
2
3
4
PIN NAME
VDD
GND
REXT
A 0
DESCRIPTION
Positive supply; connect this pin to a 2.25V to 3.3V supply.
Ground pin.
External resistor pin for ADC reference; connect this pin to ground through a (nominal) 500k Ω resistor.
Bit 0 of I 2 C address; ground or tie this pin to VDD. No floating.
5
6
SCL
SDA
I 2 C serial clock
I 2 C serial data
The I 2 C bus lines can be pulled from 1.7V to above V DD , 3.6V max.
Principles of Operation
Photodiodes and ADC
The ISL29020 contains two photodiode arrays which convert
light into current. The spectral response for ambient light
sensing and IR sensing is shown in Figure 8 in the “Typical
Performance Curves” on page 9. After light is converted to
current during the light signal process, the current output is
converted to digital by a single built-in 16-bit Analog-to-Digital
Converter (ADC). An I 2 C command reads the ambient light or
IR intensity in counts.
The converter is a charge-balancing integrating type 16-bit
ADC. The chosen method for conversion is best for converting
small current signals in the presence of an AC periodic noise. A
100ms integration time, for instance, highly rejects 50Hz and
60Hz power line noise simultaneously. See “Integration Time or
The built-in ADC offers user flexibility in integration time or
conversion time. There are two timing modes: Internal Timing
Mode and External Timing Mode. In Internal Timing Mode,
integration time is determined by an internal oscillator (f OSC ),
and the n-bit (n = 4, 8, 12,16) counter inside the ADC. In
External Timing Mode, integration time is determined by the
time between two consecutive I 2 C External Timing Mode
commands. See “External Timing Mode” on page 6. A good
balancing act of integration time and resolution depending on
the application is required for optimal results.
The ADC has I 2 C programmable ranges to dynamically
accommodate various lighting conditions. For very dim
conditions, the ADC can be configured at its lower range
(Range 1). For bright conditions, the ADC can be configured
at its higher range (Range 2).
I 2 C Interface
There are three 8-bit registers available inside the ISL29020.
The command register defines the operation of the device.
The command register does not change until the register is
overwritten. The two data registers are Read-Only for 16-bit
ADC output or timer output. The data registers contain the
ADC's or timer ’s latest digital output.
The ISL29020’s I 2 C interface slave address can be selected
as 1000100 or 1000101 by connecting A0 pin to GND or
VDD, respectively. When 1000100x or 1000101x with x as R
or W is sent after the Start condition, this device compares
the first seven bits of this byte to its address and matches.
3
Figure 1 shows a sample one-byte read. Figure 2 shows a
sample one-byte write. Figure 3 shows a sync_I 2 C timing
diagram sample for externally controlled integration time. The
I 2 C bus master always drives the SCL (clock) line, while either
the master or the slave can drive the SDA (data) line. Every
I 2 C transaction begins with the master asserting a start
condition (SDA falling while SCL remains high). The following
byte is driven by the master, and includes the slave address
and read/write bit. The receiving device is responsible for
pulling SDA low during the acknowledgement period. Every
I 2 C transaction ends with the master asserting a stop
condition (SDA rising while SCL remains high).
For more information about the I 2 C standard, please consult
the Philips ? I 2 C specification documents.
Low-Power Operation
The ISL29020 initial operation is at the power-down mode
after a supply voltage is provided. The data registers contain
the default value of 0. When the ISL29020 receives an I 2 C
command to do a one-time measurement from an I 2 C
master, it will start light sensing and ADC conversion. It will
go to the power-down mode automatically after one
conversion is finished and keep the conversion data
available for the master to fetch anytime afterwards. The
ISL29020 will continuously do light sensing and ADC
conversion if it receives an I 2 C command of continuous
measurement. It will continuously update the data registers
with the latest conversion data. It will go to the power-down
mode after it receives the I 2 C command of power-down.
FN6505.1
August 20, 2009
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ISL29021IROZ-EVALZ
EVAL BOARD FOR ISL29021IROZ
ISL29023IROZ-EVALZ
EVALUATION BOARD ISL29023IROZ
ISL29028AIROZ-EVALZ
BOARD EVALUATION FOR ISL29028
ISL29028IROZ-EVALZ
EVAL BOARD FOR ISL29028IROZ
ISL29030AIROZ-EVALZ
BOARD EVAL FOR ISL29030A
ISL29101IROZ-EVALZ
EVALUATION BOARD FOR ISL29101
ISL29102IROZ-EVALZ
EVALUATION BOARD FOR ISL29102
ISL5961EVAL2
ISL5961 TSSOPEVALUATION PLATF
相关代理商/技术参数
ISL29020IROZ-T7
功能描述:光学数位转换器 ISL29020IROZ LW PWR DIGTL OUTPUT LT SNSR RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel
ISL29020IROZ-T7
制造商:Intersil Corporation 功能描述:IC LIGHT TO DIGITAL OUTPUT SENSOR 制造商:Intersil Corporation 功能描述:IC, LIGHT TO DIGITAL OUTPUT SENSOR
ISL29020IROZ-T7A
功能描述:光学数位转换器 ISL29020IROZ LW PWR DIGTL OUTPUT LT SNSR RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel
ISL29021IROZ-EVALZ
功能描述:EVAL BOARD FOR ISL29021IROZ RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:1 系列:-
ISL29021IROZ-T7
功能描述:近程传感器 ISL29021IROZFREE DIGITL PROX SNSR RoHS:否 制造商:Vishay Semiconductors 感应方式:Optical 感应距离:1 mm to 200 mm 电源电压:2.5 V to 3.6 V 安装风格:SMD/SMT 输出配置:Digital 最大工作温度:+ 85 C 最小工作温度:- 25 C 系列:VCNL3020
ISL29022IROZ-EVALZ
制造商:Intersil Corporation 功能描述:ISL29022IROZ-EVALZ (PB-FREE ) EVALUATION BOARD - ROHS COMPLI - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL29022
ISL29023IROZ-EVALZ
功能描述:EVALUATION BOARD ISL29023IROZ RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:1 系列:-
ISL29023IROZ-T7
功能描述:光学数位转换器 ISL29023IROZ LW PWR DIGTL OUTPUT LT SNSR
RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel